Cornerstone Guide

Roof Pitch Explained: Ratio, Angle, Slope & How to Measure It

Pitch affects rafter length, material selection, drainage, snow load, and whether you can walk the roof. Everything you need — from reading a speed square to converting pitch to degrees.

Roof pitch is the rise over a 12-inch horizontal run, written as rise:12. It affects rafter length, material selection, drainage speed, snow load, and whether you can walk the roof safely. Every other roofing calculation flows from the pitch you start with.

How Roof Pitch Is Expressed

Pitch is stated as a ratio of rise to run, where run is always 12 inches. A 6:12 pitch rises 6 inches for every 12 inches of horizontal distance. You’ll also see pitch expressed as:

Contractors in the field use the ratio (6:12). Engineers and architects sometimes use degrees. Slope percentage appears on civil drawings. For roofing work, always use the ratio — it maps directly to rafter tables and speed square settings.

PitchAngleSlope %Pitch MultiplierCategory
1:124.8°8%1.003Flat / Low
2:129.5°17%1.014Flat / Low
3:1214.0°25%1.031Low
4:1218.4°33%1.054Low
5:1222.6°42%1.083Standard
6:1226.6°50%1.118Standard
7:1230.3°58%1.158Standard
8:1233.7°67%1.202Steep
9:1236.9°75%1.250Steep
10:1239.8°83%1.302Steep
12:1245.0°100%1.414Very Steep

The pitch multiplier is how much longer a rafter is than the horizontal run. Multiply the run by the pitch multiplier to get rafter line length before adding for the overhang and birdsmouth seat.

Roof Pitch Calculator

Enter rise and run, get pitch ratio, angle, rafter length, and multiplier instantly.

Open calculator →

How to Measure Pitch on an Existing Roof

You can measure pitch from inside the attic, from the roof surface, or from the ground. Each method has tradeoffs.

Method 1: Speed Square on the Rafter (Most Accurate)

In the attic, hold a speed square flat against the side face of a common rafter with the pivot point at the rafter’s top edge. The pitch reading on the square is your pitch directly. This is the most accurate method because you’re measuring the actual framing member.

Method 2: Level and Tape on the Roof Surface

Hold a 12-inch level horizontally against the roof surface. At the 12-inch mark, measure straight down to the roof surface. That vertical measurement is your rise. If you measure 5 inches, the pitch is 5:12. This method is quick but adds any error from the shingle thickness and varies if the roof surface is uneven.

Method 3: Gable End Measurement

From inside, measure the total rise (from top plate to ridge) and total run (half the building width). Divide rise by run, then multiply by 12. A house 28 feet wide with an 8.75-foot rise: run = 14 ft, rise/run = 8.75/14 = 0.625, × 12 = 7.5:12 pitch. Round to the nearest common pitch.

Minimum Pitch by Roofing Material

Every roofing material has a minimum slope requirement. Going below it voids the warranty and creates a leak. This is the most practically important use of pitch knowledge for roofers.

Roofing MaterialMinimum PitchNotes
Asphalt shingles (standard)4:122:12 with double underlayment; check local code
Asphalt shingles (low slope)2:12Requires two layers of ice-and-water shield
Metal standing seam1:12 to 3:12Varies by panel profile; check manufacturer spec
Metal exposed fastener3:12Lap seams require steeper pitch to drain
Cedar shake / wood shingle3:12 to 4:124:12 recommended for longevity; 3:12 minimum
Concrete / clay tile4:12Some profiles go to 3:12 with underlayment
Slate4:12Steeper is better; 6:12+ recommended
EPDM / TPO (flat membrane)1/4:12Minimum drainage slope; engineered drainage required
Modified bitumen1/4:12With tapered insulation system for drainage
Built-up roofing (BUR)1/4:12Low-slope commercial application
Metal shingles3:12Some manufacturers allow 2:12 with extra underlayment
Corrugated polycarbonate2:12Pergolas, carports; check panel lap spec

Warranty void below minimum: Installing asphalt shingles below 4:12 without the specified additional underlayment voids the manufacturer warranty in most cases. For a 2:12–4:12 installation, two layers of ice-and-water shield are required over the entire roof deck, not just at the eaves.

Pitch and Snow Load

Snow does not stay on a steep roof. It stays on a flat one. The relationship between pitch and snow load is critical in Canada and the northern US. Key thresholds:

For Ontario, Quebec, and the Prairie provinces, a 6:12 minimum is common practice on new construction. Below that, snow accumulation creates cumulative load risk over the winter.

Pitch and Walkability

Walkability is important for installation and maintenance. The practical thresholds:

Common Pitch Mistakes in Residential Framing

Frequently Asked Questions

What is the most common roof pitch for residential homes?

In North America, 4:12 to 6:12 is the most common range for residential construction. 6:12 is especially common in snow-country regions (Ontario, Quebec, Prairies, upper Midwest) because it sheds snow reliably. 4:12 is common in warmer, drier climates where snow load is minimal.

What is a 4:12 pitch in degrees?

A 4:12 pitch is 18.4 degrees. The formula is arctan(rise/run) = arctan(4/12) = arctan(0.333) = 18.4°. Your speed square shows this as the 4 mark on the pitch scale.

What pitch is too steep for asphalt shingles?

There is no upper limit for asphalt shingles — they can be installed on any pitch steep enough to drain (2:12+). The practical limit is walkability and installation safety, not the material. Steep roofs (10:12+) require extra staging and labor; the shingles themselves are fine.

How do I convert pitch to degrees?

Use the formula: degrees = arctan(rise / 12). For a 6:12 pitch: arctan(6/12) = arctan(0.5) = 26.6°. On a calculator, use the inverse tangent (tan&sup{-1;}) function. The pitch calculator on this site converts automatically.

What is a pitch multiplier?

The pitch multiplier converts horizontal run to rafter length. It equals √(1 + (rise/12)²). For 6:12: √(1 + 0.25) = √1.25 = 1.118. Multiply the horizontal run by 1.118 to get the rafter line length. This accounts for the longer diagonal path of the rafter compared to the horizontal run.

Can I change my roof pitch without replacing the entire roof structure?

Changing pitch requires reframing the roof — new rafters, new ridge, new top plates at the correct height. It is a substantial structural project that requires a permit and typically an engineer’s involvement. The only exception is converting a flat or very low-slope roof to a slightly higher slope using tapered insulation (no structural change) or adding a new roof structure over the existing one.

Related Calculators & Guides