Rafter Framing Guide

Rafter Sizing Guide: What Size Rafter Do You Need?

Rafter size comes down to span, spacing, species, and snow load. Here’s how to read span tables, pick the right lumber size, and know when an engineer is required.

Rafter size depends on span, spacing, species group, and load. For a 16-foot span at 16″ o.c. in typical Canadian conditions (2.0 kPa snow + 0.5 kPa dead), a 2×10 No.2 Douglas Fir is the minimum. Most residential roofs need 2×8 to 2×12 common rafters; anything over 20 feet calls for an engineer.

The Four Variables That Determine Rafter Size

Every rafter sizing decision involves four inputs. Change any one and the required lumber size can change:

  1. Horizontal span: The horizontal distance from the outside wall plate to the ridge (not rafter line length). This is what span tables are keyed to. A rafter with a 14-foot line length at 6:12 pitch has a horizontal run of about 12.5 feet.
  2. Spacing: On-center spacing between rafters — typically 12″, 16″, or 24″. Wider spacing means each rafter carries more tributary area, requiring a larger size.
  3. Lumber species and grade: Span tables are organized by species group. Douglas Fir-Larch (common in BC and western Canada) outperforms Spruce-Pine-Fir (eastern Canada, much of the US) at the same dimensions. Using the wrong column means over- or under-sizing.
  4. Load: Includes dead load (roofing materials, sheathing, framing) and live/snow load. Higher snow loads = shorter allowable spans.

Reading Rafter Span Tables

The NBC (National Building Code of Canada) and IRC (US) both publish rafter span tables. Here’s how to read them:

  1. Find the column for your species and grade (e.g., S-P-F No.2)
  2. Find the row for your rafter size (e.g., 2×10)
  3. Find the sub-column for your spacing (12″, 16″, or 24″ o.c.)
  4. The number in the cell is the maximum allowable span (horizontal, not rafter line length)
  5. If your span exceeds the table maximum, go to the next larger lumber size or reduce spacing
Rafter SizeDouglas Fir No.2Spruce-Pine-Fir No.2Hem-Fir No.2
16″ o.c.24″ o.c.16″ o.c.24″ o.c.16″ o.c.24″ o.c.
2×69’-0″7’-11″8’-6″7’-5″8’-3″7’-2″
2×812’-2″10’-7″11’-5″10’-0″11’-1″9’-8″
2×1015’-5″13’-5″14’-6″12’-7″14’-1″12’-3″
2×1218’-9″16’-4″17’-8″15’-5″17’-2″14’-11″

Approximate values for 1.4 kPa live load + 0.5 kPa dead load (typical southern Ontario conditions). Always verify with the applicable span tables for your jurisdiction and design snow load.

Span is horizontal, not along the rafter: Span tables list the maximum horizontal distance. Your rafter is longer because it travels at an angle. Use the pitch multiplier to convert: rafter line length = horizontal span × pitch multiplier. For 6:12, multiplier = 1.118.

Common Rafter Sizes and Typical Applications

Lumber SizeTypical ApplicationMax Horizontal Span (16″ o.c., S-P-F No.2, low snow)
2×6Sheds, garages, small additions~8’-10’
2×8Standard residential, moderate spans~11’-13’
2×10Longer spans, higher snow loads~14’-16’
2×12Large open floor plans, high snow~17’-19’
LVL / EngineeredSpans over 20’, complex loadsEngineer required

Species Groups: Which Column to Use

Canadian lumber is graded under NLGA rules and typically falls into these species groups for span table purposes:

In Ontario, essentially all framing lumber is S-P-F. Using a Douglas Fir table for an Ontario project gives unconservative (too long) allowable spans. Always match the column to the actual lumber on the job.

When You Need an Engineer

Span tables cover prescriptive cases. An engineer is required when:

Frequently Asked Questions

What size rafter do I need for a 16-foot span?

For a 16-foot horizontal span at 16″ o.c. in S-P-F No.2 (Ontario standard), you need a 2×12 or a 2×10 at 12″ o.c. At 6:12 pitch, the actual rafter line length is about 17.9 feet. Always confirm against the span table for your specific snow load and species.

What is the difference between rafter span and rafter length?

Span is the horizontal distance the rafter covers (from wall plate to ridge). Length is the actual distance along the rafter (longer than span because the rafter is angled). Span tables use horizontal span. Rafter length = span × pitch multiplier.

Is 2x6 big enough for rafters?

For spans up to about 9–10 feet at 16″ o.c. in moderate snow loads, yes. For a typical residential house with a 12–16 foot run, 2×6 is undersized — you need at least 2×8. 2×6 is appropriate for sheds, garages with small spans, or supplemental shed roofs over additions.

Can I use 2x8 rafters for a 14-foot span?

At 16″ o.c. in S-P-F No.2, a 2×8 allows approximately 11–12 feet horizontal span in moderate snow loads. A 14-foot span typically requires 2×10. Confirm against your jurisdiction’s span tables for the applicable snow load.

Related Calculators & Guides