Roof Area Calculator
Enter the building size and roof pitch. Get roof area, roofing squares, and a full material list for gable, hip and shed roofs.
Shingles shed water, they do not seal it out. A roof this flat needs a membrane.
-
Self-adhered modified bitumen roll roofing (cap sheet + base sheet)Peel-and-stick two-layer system. The usual DIY-friendly choice for low-slope porches and additions.Check price
-
EPDM rubber roofing kitOne-piece membrane for small flat and low-slope roofs.Check price
-
Self-adhered ice and water shieldSeals the deck where the low-slope section ties into a shingled roof.Check price
RooferToolkit may earn a commission on purchases made through these links, at no cost to you.
Shingles are allowed here only over two layers of underlayment, or a full self-adhered membrane. The roll count above is already doubled.
-
Synthetic roofing underlayment (10 sq roll)Lapped 19" for double coverage on low slopes.Check price
-
Self-adhered ice and water shieldFull-deck coverage is the belt-and-braces option on a low-slope shingle roof.Check price
-
Plastic cap roofing nailsHold underlayment flat until the shingles go on.Check price
RooferToolkit may earn a commission on purchases made through these links, at no cost to you.
At 8:12 and up you cannot walk the roof safely. Set up staging and tie off before you load shingles.
-
Roof jacks / roof brackets (adjustable, 2×6)Nail-on brackets that hold a plank to stand and stack bundles on.Check price
-
Roofing fall protection kit (harness, rope, anchor)Reusable ridge anchor, rope grab and full-body harness in one bucket.Check price
-
Roofing nailer (coil)Steep roofs need six nails per shingle on most products. A coil nailer keeps up.Check price
RooferToolkit may earn a commission on purchases made through these links, at no cost to you.
Roof Pitch Multiplier Table
Multiply the roof footprint by the multiplier to get the real roof area. Example column uses a 1,000 ft² footprint.
| Pitch | Angle | Multiplier | 1,000 ft² footprint | Squares | Shingles |
|---|
How to Calculate Roof Area
Roof area is always bigger than the floor plan under it, because the roof is sloped. Measure the footprint from the ground, then multiply by the pitch multiplier.
Roof area = (Length + 2 × overhang) × (Width + 2 × overhang) × Pitch multiplier
Pitch multiplier = √(1 + (Rise ÷ 12)²)
A 40' × 28' house with 12" overhangs has a 42' × 30' roof footprint, or 1,260 ft². At 6:12 the multiplier is 1.118, so the roof is 1,409 ft², or 14.1 squares. A gable, a hip and a shed roof over the same footprint at the same pitch all have the same area. What changes is the trim: ridge, hips, rakes and eaves.
What a roofing square is
One square is 100 ft² of roof. Shingles, underlayment and labor are all priced by the square. Three-tab and most architectural shingles come three bundles to the square. Heavier designer shingles run four or five.
Picking a waste factor
- 10%: plain gable, two planes, no valleys.
- 15%: hip roof, or a gable with a couple of valleys or dormers.
- 20%: cut-up roof with several hips, valleys and dormers.
- 25%: steep and cut-up, turrets, lots of short courses.
Round up, not down. Running short means a second delivery, and the new bundles may not match the color lot on the roof.
Pitch limits for shingles
IRC R905.2.2 allows asphalt shingles only at 2:12 and steeper. From 2:12 up to 4:12 they need double underlayment. Below 2:12 use a membrane roof. See Roofing Material Pitch Requirements for every material.
Frequently Asked Questions
How do I calculate roof area from the ground?
Measure the building length and width, add the overhang to each side, and multiply the two to get the footprint. Then multiply by the pitch multiplier for your roof pitch. For a 6:12 roof the multiplier is 1.118.
How many bundles of shingles are in a square?
Three bundles for 3-tab shingles and for most architectural shingles. Heavy designer shingles can take four or five bundles per square. The coverage is printed on the bundle wrapper.
How many squares is a 2,000 square foot roof?
20 squares, because one square is 100 square feet. With a 15% waste factor you would order 23 squares, which is 69 bundles at three bundles per square.
Does a hip roof have more area than a gable roof?
No. Over the same footprint and at the same pitch they have the same area. A hip roof needs more waste and more cap shingles, because every hip is cut and capped.
How much waste should I add for shingles?
10% for a simple gable, 15% for a hip roof or a roof with a few valleys, and 20% to 25% for steep or cut-up roofs.