Rafter Layout Guide

Plumb Cut Angle: How to Find It for Any Pitch

The plumb cut angle is the single most important angle in roof framing. It applies to every cut on every rafter — ridge, birdsmouth, overhang, hip, and valley.

The plumb cut angle = arctan(rise ÷ 12). For 6:12: arctan(0.5) = 26.6°. Set your saw to this angle for the ridge cut, birdsmouth heel cut, and the plumb face of all hip and valley cheek cuts. The level cut is always 90° minus the plumb cut angle.

Why the Plumb Cut Angle Matters

Every compound cut in roof framing comes back to the plumb cut angle. It’s the angle that a vertical plane makes with the rafter when the rafter is in position on the roof. It applies to:

PitchPlumb Cut AngleLevel Cut AngleSpeed Square Setting
3:1214.0°76.0°Mark at 3 on pitch scale
4:1218.4°71.6°Mark at 4
5:1222.6°67.4°Mark at 5
6:1226.6°63.4°Mark at 6
7:1230.3°59.7°Mark at 7
8:1233.7°56.3°Mark at 8
9:1236.9°53.1°Mark at 9
10:1239.8°50.2°Mark at 10
12:1245.0°45.0°Mark at 12 (both cuts equal)

Using a Speed Square to Mark the Plumb Cut

The speed square is the fastest and most accurate tool for marking plumb cuts in the field. The procedure:

  1. Place the pivot point (corner of the speed square) at the top edge of the rafter with the lip hooked over the edge
  2. Rotate the square until the pitch reading on the body of the square aligns with the top edge of the rafter
  3. Mark along the vertical (right-angle) edge of the square — this line is the plumb cut
  4. For the level cut, flip the square: use the degree scale set to the complement angle, or simply mark perpendicular to your plumb line

The speed square pitch scale is calibrated for the rise per 12 inches of run — the standard pitch ratio. Set it to 6 for 6:12, 8 for 8:12, and so on. The degree scale (0°–90°) is also present and can be used for non-standard pitches.

Setting a Circular Saw to the Plumb Cut Angle

When cutting multiple rafters at the same angle, setting the saw bevel is faster than marking each cut individually. The procedure:

  1. Calculate the plumb cut angle from the table above
  2. Set the saw bevel to that angle. The saw bevel is measured from perpendicular to the blade, which is the same as the plumb cut angle measured from vertical
  3. Hold a test piece vertically (plumb) and check the cut against a level — the cut face should be exactly vertical when the rafter is in position
  4. Test on a scrap piece first; the bevel gauge on a circular saw can be off by 0.5–1°

For a 6:12 pitch, set the saw bevel to 26.6°. Many saws have detents at 22.5° and 30° — 6:12 falls between them and requires a freehand bevel setting. Use a digital angle gauge for precision.

Plumb Cut Angle vs. Saw Bevel Setting

This confuses a lot of framers. The plumb cut angle is measured from vertical; the saw bevel is also measured from vertical (from the perpendicular to the blade). They are the same number. If the plumb cut angle is 26.6°, the saw bevel is 26.6°.

Some older resources state the saw angle differently — as the complement (90° minus the plumb angle) measured from horizontal. Always confirm which convention your saw and reference use before making the first cut.

Hip and Valley Rafter Cheek Cuts

Hip and valley rafters require a compound cut at the ridge — a plumb cut combined with a side (cheek) cut that angles the end so it fits against the ridge or corner without a gap. The cheek cut is a second bevel that runs in the horizontal plane.

For a regular hip or valley on a square building with equal pitches on all sides:

For unequal pitches (different pitches on intersecting roof planes), the cheek cut angle changes. Use the hip/valley rafter calculator for those cases.

The Level Cut Relationship

The plumb cut and level cut are always complementary — they add to 90°. This is because the rafter, wall, and roof surface form a right triangle. The plumb cut is the vertical leg; the level cut is the horizontal leg. For any pitch:

Level cut angle = 90° − Plumb cut angle

For 6:12: Level cut = 90 − 26.6 = 63.4°. This appears at the seat cut of the birdsmouth and at the tail cut of the overhang if the tail is cut level (square to the wall) rather than plumb (parallel to the building face).

Plumb Cut Angle Calculator

Enter pitch, get plumb angle, level angle, and saw settings for every cut on the rafter.

Open calculator →

Rafter Tail Cut Options

At the overhang end of the rafter, the tail can be cut in two ways:

Common Mistakes

Frequently Asked Questions

What is the plumb cut angle for a 6:12 pitch?

26.6 degrees. Calculated as arctan(6/12) = arctan(0.5) = 26.6°. Set your circular saw bevel to 26.6° for the ridge cut and birdsmouth heel cut on a 6:12 roof.

Is the plumb cut angle the same as the saw bevel setting?

Yes. The plumb cut angle (measured from vertical) equals the saw bevel setting (also measured from perpendicular to the blade, which is vertical). A 26.6° plumb cut = a 26.6° saw bevel setting.

What angle do I set my speed square for a 6:12 pitch?

Set the speed square to 6 on the pitch scale (the rise-per-12 scale on the body of the square). Hook the lip over the top edge of the rafter and mark along the perpendicular edge for the plumb cut line.

How do I cut a plumb cut on a hip rafter?

A hip rafter plumb cut is a compound miter: the bevel equals the common rafter plumb cut angle (same pitch), and the miter is 45° for a regular hip on a square building. Set both simultaneously on a compound miter saw or make two passes with a circular saw.

What is the level cut angle for a 6:12 pitch?

63.4 degrees. The level cut is always the complement of the plumb cut: 90° − 26.6° = 63.4°. This angle applies to the seat cut of the birdsmouth and to level tail cuts at the overhang.

Related Calculators